Olympia Chimney Chimney Liner & Rebuild Nationwide

Olympia Chimney Chimney Liner & Rebuild in Kennesaw: What to Know First

We provide independent Olympia Chimney chimney liner & rebuild service in Kennesaw, with most liner replacements and partial rebuilds completed in one to two days after the Level 2 inspection. Every job starts with a camera-scan of the flue, a written price, and a photo record - nothing is scheduled until you have both in hand. If you own an Olympia Chimney stainless steel liner or flexible liner system and you’re seeing rust flakes in the firebox, drafting problems, or a creosote pattern that doesn’t make sense, call (678) 535-2204. Corrine Halstead and our crew have worked on Olympia Chimney products in Kennesaw homes since 2015, including the older two-story colonials near Kennesaw Mountain where clay-to-steel liner retrofits are common.

Call (678) 535-2204

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia Chimney 316Ti flexible liners in Kennesaw’s freeze-thaw cycles. The 316Ti alloy handles acid well but the flex joints at the offset (where the flue bends to miss a rafter) work-harden over Georgia winters. We’ve pulled collapsed sections in Kennesaw’s Acworth and Lost Mountain neighborhoods where the offset angle exceeded 30 degrees during original install. We replace with a properly supported rigid or semi-rigid run, or sleeve the joint with DuraFlex if the rest of the liner tests sound.
• Olympia Chimney’s original smooth-wall rigid series with factory condensation collars. The collar seam is a cold spot; in Kennesaw’s humid shoulder seasons, acidic condensate pools and eats the weld from the outside in. Homeowners smell vinegar or see white efflorescence on the exterior brick before they notice draft loss. We cut back to sound metal, install a Gelco condensation drain tee if the appliance is high-efficiency, and document the repair with photos under Haven Standard Clause 4.
• Olympia Chimney’s pre-2018 flexible liner termination caps with internal mesh. The mesh spacing was too fine for Georgia’s pollen-heavy springs and Kennesaw’s oak catkin season. Clogged caps back-puff smoke into the room and accelerate creosote formation in the upper flue. We replace with Famco’s wider-mesh equivalent or a Gelco top-mount damper cap, depending on whether the homeowner burns wood or runs a gas insert.
• Olympia Chimney’s transition plates where a stainless liner meets a clay thimble. The plate is stamped to one standard angle; Kennesaw’s 1960s-80s ranch homes often have 45-degree thimbles that don’t match. Gaps get packed with refractory cement that cracks in two seasons. We fabricate a custom transition or source an Olympia-compatible adjustable plate through our Haven buying network, then seal with HeatShield Cerfractory foam for a joint that moves with the stack.
• Olympia Chimney’s UL 1777 listed liners paired with oversized fireplaces. The liner is rated for the appliance BTU, not the firebox volume. In Kennesaw’s newer construction with tall, shallow Rumford-style openings, the liner runs below its dew point, condensing flue gases into creosote washes. We calculate the actual firebox-to-flue ratio during our Level 2, then upsize the liner or recommend a properly sized insert - we write it down before we ask you to decide anything.

Our Olympia Chimney Chimney Liner & Rebuild Process

1. 1
   Level 2 camera inspection. We run a chimney scan camera the full length of the Olympia Chimney flue liner, record video and stills, and mark GPS coordinates of every defect. You get the footage before we talk price.
2. 2
   Written scope and price. Haven Standard Clause 1: a written price, written scope, and written warranty delivered before anyone schedules work. No verbal estimates, no “we’ll see when we get there.”
3. 3
   Parts decision with options. If your Olympia Chimney liner is discontinued or back-ordered, we quote OEM-equivalent from DuraFlex, HeatShield, or Gelco sourced through our Haven buying network. You see the part numbers and warranty terms in writing.
4. 4
   Repair or rebuild. Liner pull and replacement, partial rebuild of the smoke chamber and throat, or full chimney rebuild from the roofline up - done by background-checked, uniformed techs with license numbers on the invoice.
5. 5
   Post-repair camera verification. We re-scan the completed flue, test draft with a manometer, and photograph the exterior termination. This documentation goes into your record under Haven Standard Clause 4.
6. 6
   365-Day Done Right Promise activation. The warranty is stamped, dated, and emailed with your photo archive. If it’s not done right, we make it right.

Before

After

What Olympia Chimney Chimney Liner & Rebuild Costs in Kennesaw

These are real Kennesaw-market prices based on jobs we’ve completed in zip codes 30144 and 30152, not national averages. The exact number depends on what the camera shows. Call (678) 535-2204 for a free estimate - we bring the camera to the estimate, so there’s no guesswork in the quote.

Why Kennesaw Homeowners Call Level Two Chimney Kennesaw for Olympia Chimney Work

We’ve completed more than 38,000 chimney inspections and cleanings since 2009, every one with a written price before work started and a documented record when done. Our techs know Olympia Chimney’s product evolution - which 316Ti lots had the offset-joint issue, which termination caps clog, where the factory welds fail - because we’ve pulled enough of them to see the patterns. When Olympia parts are back-ordered, we don’t leave you waiting; our Haven buying network stocks DuraFlex, HeatShield, Gelco, and Famco equivalents at prices kept honest through group purchasing. Background-checked, uniformed technicians. License number on every page. Live person on the phone 24/7. And our Free Second Opinion on any written estimate means you can shop with confidence - bring us a competitor’s quote and we’ll tell you straight if it’s right.

FAQs